Woodworking Equipment at Draigsffau

Power (Floor) Tools Safety Equipment Hand-Held & Measuring Tools Bits & Blades

Power Tools

Make & Model
Table Size
Work Size
Cut Size
Blade (and Feed, if applicable)
Overall Size
HP
Amps
Weight
(Pounds)
Delta 36-444 10-inch Contractor's Table Saw with Incra fence, table extensions, and attached router table
(Blades)
71½"W x 27"D x 38"H, tilt 45°R to 0°L
 Unlimited. Rip cuts max. 30"R, 13½"L of blade
3¼" max. depth (2-1/8" at 45°), 13/16 max. width (dado)
10" diam., 5/8" arbor, 3,000 RPM
76½"W x 43"D x 38"H
12.8
220 
Jet JPM-13CS 13-inch Planer/Molder
14"W x 36½"L x 28½"H
13"W x 6-1/8"H,
14" min. length
13"W, 1/8" max. depth, 1/16" max. depth at full width
3 knives, 4,500 RPM, 13,500 cuts/min. Feed rates 20 and 10 ft./min.
 23"W x 36½"L x 43½"H
 15
242
Jet JJ-6CSX 6-inch Jointer
7-3/8"W x 46"L x 31¾"H, tilt 45°R to 45°L
6" max. width, 10" min. length
6-1/16"W x ½" max. depth (stop at 1/8"). Taper cut @ 1/8" depth is 1/16" over 10".
3 knives, 6-1/16"L x 5/8"W x 1/8"T, 4,800 RPM
20"D x 46"L x 31¾"H
1
 11
258
Jet JWBS-18 18-inch Bandsaw
(Blades)
19" x 19" x 37½"H, tilt 45°R to 10°L
18-3/8"W (16"W if resawing) x 10¼"H
10¼"H
133"L, 1/8" to 1½" wide, 3000 ft./min.
28½"D x 37¾"W x 72"H
16 
320
Grizzly G7944 14-inch Floor Drill Press with QuickStopLP drill press table
(Bits)
(Speeds)
51¼" x 13¾" x 18½" to 50"H, 360° rotation, tilt ±90°
14"W x 31½"H
3¼" spindle travel. To ¾" diam. in steel.
Chuck 1/8" to 5/8". MT #2. 12 speeds: 140, 260, 320, 380, 480, 540, 980, 1160, 1510, 1650, 2180, 3050 RPM. Motor 1725 RPM.
24"D x 14"W x 64"H
¾
9
172
Performax 16-32 Plus 16-inch Drum Sander
(Abrasive Strips)
17"W x 42½"L x 35¼"H 
32" max. W x 2¼" min. L x 1/32" (min.) to 3" (max.) H
16"W
5"diam. x 16"W drum, 1700 RPM. Feed rate 0 to 10 ft./min.
33"W x 42½"L x 51½"H
14
141
Delta 46-250 Midi-Lathe with Bed Extension
(Turning Tools)
(Speeds)
not applicable
10" diam. x 14½"L (37"L with bed extension)
not applicable
500, 800, 1250, 1800, 2650, or 3700 RPM
11"W x 33¼"L x 17½"H
½
6.6
85

DeWalt 758 8-inch Bench Grinder
(Polishing Compounds)

2 tool rests, 2" x 4" each
not applicable

1" x 8" diam. x 36 grit wheel (5/8" hole)

1" x 8" diam. x 60 grit wheel (5/8" hole)

8" diam., 5/8" arbor, 3,600 RPM

17¼"W x 10½"D x 12¼"H
¾
4.2
39½

Delta 23-700 Sharpening Center

Accu-Sharp AS502 Sharpening Jig


not applicable
not applicable

5/8" x 5" diam. x 100 grit dry wheel (½" hole)

2" x 10" diam. x 220 grit wet wheel (7/8" hole)

dry (grinding) wheel 3450 RPM

wet (honing) wheel 70 RPM

13"W x 15"D x 12"H
1/5
2
32
Porter-Cable 7518 Router
(mounted in router table)
(Bits)
 71½"W x 27"D x 38"H
Unlimited
 depends on bit
½" collet (¼" w/ adapter). 10,000, 13,000, 16,000, 19,000, or 21,000 RPM
 11"W x 7" D x 11"H
 15
14½ 
Wacker WP 1550A Vibrating Plate Compactor
No, I haven't really figured out how to use this for woodworking. We use it for compacting sand and gravel for masonry or concrete work.
(gas)
190

Safety Equipment

Make & Model
Capacity
Port Size
Overall Size
HP
Amps
Weight (Pounds)
JDS Air-Tech 2000 Model 750 Air Filter
200 to 750 CFM
11" x 23"
12"H x 24"W x 34"L
 
3.9
62
Jet DC-650 Dust Collector
650 CFM, 7.8"H2O
4" (1)
27"W x 14"D x 66"H
1
11
84
Universal 80-VC Propane-fueled Convection Heater
30,000 to 80,000 BTU
 
14" diam.
N/A
N/A
20

Back to Woodworking at Draigsffau

Back to the Door of Draigsffau.     To the Site Map.

© 2002 - 2004 by Christopher M. Albrecht
All graphics copyright the respective manufacturers.